Original Item: Only One Available. Austria-Hungary purchased about 416,000 German helmets from November 1916 until the end of the war, and also began its own licensed production starting in May 1917. Around a million Stahlhelm of all variants were issued until the end of the war. The Austrian M17 helmet was similar to the German M16 but was colored golden-brown (known as Isonzo-braun), had a cloth chinstrap and had the chinstrap rivet located higher up on the steel shell. From May 1917 till the end of World War I 534,013 were produced, many of which were manufactured at the Krupp plant in Berndorf, Lower Austria.

This is a really nice, excellent example of a WWI M17 Austro-Hungarian Helmet that was converted for use by the Third Reich in the 1930s before the issue of the M1935 helmet. The original "Isonzo braun" paint was removed, and then WWII early war "Apfel-grün" (Apple Green) paint was applied, which is still present, retained at about 80%. Both of the early chinstrap retaining bales are intact, and pressed flat, as was done when the Austrian helmets were being reconfigured by the Germans. It features a correct M31 eight finger leather liner (Marked size 56) and wonderful Heer (army) decal over the left ear and National decal over the right. Both decals are mostly complete and are retained at approximately 85%.

There is no maker or size marking stamped on the shell, however this is typical for Austro-Hungarian M17 helmets, as many of the makers used only ink stamps, easily painted over. It does however have a clear 5 1 2 1 rolling mill lot number stamped onto the inside of the dome. We measured the outside of this helmet, and we are fairly certain that it is in size 66cm. This is a nice large size that would usually accommodate size 56 to 58 hat sizes, which is 7 to 7 1/4 in U.S. sizes. The helmet still has the correct short vent hole lugs without steps, for attachment of a "stirnpanzer" helmet plate. Smaller sized helmets would have a step, but this does not, confirming its larger size.

All three liner retaining pins are intact, and they are WWII German style, not the original Austrian style. The liner band is aluminum, with square aluminum chin strap loops attached to reinforced sides. This is the last pattern before the move to galvanized steel bands. The left exterior of the liner band is marked 66 / 56, indicating that it is a size 56 liner for a size 66 shell. This is quite interesting, as usually size 66 band liners were only made for 58 and 59 inner bands, so this may have been customized for this specific helmet.

It is also maker marked and dated on the other side:

Metall-Lederverarbeitung W.Z.
1940
Bln.- Ch'burg 5

This indicates production by the metal and leather working company Werner Zahn, based in Berlin - Charlottenburg, in the year 1940, which fits right into the early war period. It is possible that it was replaced at some point, as the paint on the liner split pins is a bit darker than the exterior paint. Liner has separated about ⅓ around the inner liner band. It does not detract too much from the outward appearance and displayability of the helmet, however.

This is a very nice example of a WWII reissued Austrian M17 helmet, one of the few that we have been able to offer. Ready to fill a spot in your helmet collection!

The first "modern" steel helmets were introduced by the French army in early 1915 and were shortly followed by the British army later that year. With plans on the drawing board, experimental helmets in the field, ("Gaede" helmet), and some captured French and British helmets the German army began tests for their own steel helmet at the Kummersdorf Proving Grounds in November, and in the field in December 1915. An acceptable pattern was developed and approved and production began at Eisen-und Hüttenwerke, AG Thale/Harz, in the spring of 1916. These first modern M16 helmets evolved into the M18 helmets by the end of WWI. At the end of WWI it is estimated that Germany had produced about 8,500,000 steel helmets. As a result of the restrictions placed on the German’s by the Treaty of Versailles, which dictated a standing army of only 100,000 personnel, there was an abundant surplus of these helmets, and though they saw widespread use by Freikorps personnel, there was still a stockpile controlled by the Reichswehr.

These excess helmets underwent minor modifications in 1923 with the addition of provincial identifying shield decals and in 1931 with the development of a new chinstrap and liner system. Although helmet development was ongoing when AH came to power in 1933, the M16 and M18 helmets were still the main headgear worn by the Reichswehr. The helmets remained the same until March 1933 when the provincial shields were discontinued in favor of the national tri-color shield. In 1934 the national eagle shield was introduced, and both the tri-color and eagle shields were applied to the helmets. After the development of the new M35 helmet, the WWI helmets were still issued to second line and training troops well into WWII. The Austrian M16 was almost identical to the German version with the positioning of the chinstrap liner rivets being the most readily identifiable difference.

Austro-Hungarian Helmets

The Central Powers of Austria-Hungary used, manufactured and commissioned, variations of the World War One German Stahlhelm M16 design. The Austrian M1917 helmet was similar to the German M1916, but had a few variations including the chinstrap, chinstrap rivets located higher up on the steel shell and variations in locations of markings among others.

Early Austrian helmets were supplied by Germany, the first shells supplied as the chinstrap rivets were mounted in a lower position. The Austrians fitted their own chinstrap bales, chinstraps and liner and painted them in Austrian Isonzo braun. These modifications were carried out with German machinery at the "Adolf Westen di Cilli factory, which is now Celije, in Slovenia.

Later Austria-Hungary made their own helmets, and eventually developed a model similar to the German M18, but it did not see wide use before the end of the war, just as with German's M18. Both were an an important stepping stone towards the German helmets of WWII, which moved to chin straps attached to the liner, not the shell.

Austro-Hungarian WWI Helmets Makers-

There are only 9 known factories that produced helmets during WWI for the KUK. Unlike the Germans the Austrian pattern helmet are often found without factory stamps and heating lot codes. When the heating lot codes are present it is often on the outer top dome of the helmet instead of the inside. The following is a table of Manufactures codes of helmets produced by the Austrians. Several of these makers did not stamp the code into the shell of the helmet but rather marked them with an ink stamp. Therefore many Austrian shells will be encountered today that seem to have no maker mark as the ink stamp has worn off, but most will have rolling mill codes.

Maker Name Factory Location Maker code Sizes Model

A. Westen Cilli Celie, Slovenia AW 64 M17

Brüder Gottlieb u. Brauchbar Brunn BGB 66 M17

C. A. Scholtz,Mateocz Sloeakei CAS 66 M17

Berndorfer Metal-Warenfabrik Berndorf, Austria "Bear" logo 66,64

Bruder Lapp, Rottenman u. Warcholowsky Unknown ? M17

Nadrag,Transilvania Transylvania Unknown ? M17

Resicka, Transylvania Transylvania Unknown ? M17

Bleckmann & Poldihutte Klando Boemia Unknown x Stirnpanzer

Gebruder Bohler & Co., Kapfen Austria, Stiria GB "Star" 66 M17

Rolling Mills Marker Code

Ludwikow L

Bleckmann B

Poldi P